STE P 4: Assembly Of Exhaust Hood (See Figure 3)
A. Remove screw B.
B. Place side exhaust hood against the rear and side of microwave unit.
C. Align hole inside exhaust and mirowave unit, reinstall screwremoved
in st ep A.
D. Install side exhaust front screw to attach side exhaust hood to the
microwave unit.
E. Place top exhaust hood so hole at front aligns with hole in microwave
unit.
F. Install 2² shoulderscrewtoattachtopexhausthoodtomicrowaveunit.
G. Installrearscrewtoattachtopexhausthoodtosideexhausthoodside.
STE P 5: Instal lation Of Microwave “L” Bracket
(See Figure 3)
A. Attach “L”bracket with #10 screw to lower rear panel of microwave.
STEP 6: Instal lation Of Microwave Mount Bracketry
(See Figure 2)
Side Brackets
A. Measure 14 5/8² up from the bottom of the cutout tothe bottom edge
of the side mounting brackets.
B. Use two flat head screws to attach each side mounting bracket tothe
cabinet side walls as shown.
NOTE: Sidemountingbracketshouldbepushed flushto cabinetface.
Microwave Base Bracket
A. With dimension “B” from figure 2, measure and mark location for
microwave base bracket.
B. Withthetwotrusshead screws, attachmicrowavebasebracket tothe
floor of cabinet as shown.
STEP 7: Installation Of Microwave
A. Plug power cord of oven into receptacle.
B. Slidethemicrowavefeetintolocatingslotsinmicrowavebasebracket.
NOTE: Microwave rear cabinet should be flush to microwave base
bracket rear flange.
C. Slide “L” bracket over the two shoulder screws on bottom side of
microwave.
D. With two flat head screws, attach “L” bracket and microwave base
bracket to cabinet face. (See figure 4)
E. Attach trim assembly as shown in figure 4. Insert bottom of trim
assemblyintolowersupportandrotateupward.Marklocationofscrew.
Remove trim anddrill 9/64 pilot holeat markedlocations andreinstall
trim, attach top of trim to cabinet with 2 flat head screws.
FIGURE 4
INSTALLATION A BOVE LOWER OVEN
NOTE: When installing this kit above a built-in oven, check built-in oven
installationinstructionstodeterminecutoutdimensionsforthe(lower)wall
oven.
NOTE:Foranewinstallation,the48² heightdimensiontothebottomofthe
cutoutforthemicrowaveovenisrecommended.Thisplacesthemicrowave
oven bottom at approximately 50² from the floor. See figure 5.
When the microwave oven is installedabove a walloven,
theminimumheightdimens ionfromthebottom of thewall
ovenc utouttothebottomofthemicrowavecutoutmustbe
maintained.
CAUTION
MIN.
1²
28-3/4²
16-1/16²
48²
(See
Note
2)
FIGURE 5
MMA27 Kits may be used with microwave model MMC5000 installed
above 27² wall oven models bearing manufacturer No. E25378, when
installedinaccordancewithManufacturer’sInstallationInstructions.These
include models MEW5527 & MEW6527.
MMA30maybeusedwithmicrowavemodelMMC5000installedabove30²
wall oven models bearing manufacturer No. E25378, when installed in
accordance with Manufacturer’s Installation Instructions. These include
models MEW5530 & MEW6530.
Manufacturer’sNo. can beobtained fromthe serialplate on thewall oven.
IMPORTANT
SAVE FOR LOCAL ELECTRICAL
INSPECTOR’S USE
(1 strony)
(48 strony)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji